nybjtp

Tasi-Layer Fe'avea'i PCBs Tasi-Sisi Fetuutuunai Lolomi laupapa laupapa mo Consumer Electronic

Fa'amatalaga Puupuu:

Fa'ata'ita'iga: PCB Fe'avea'i Fa'afuafua e tasi

Fa'aaogāga o oloa: Consumer Electronic

Laupapa laupapa: 1 apa

Mea fa'avae: Polyimide(PI)

I totonu Cu mafiafia:/

Quter Cu mafiafia: 18um

Ufiufi lanu ata: Samasama

Solder mask:/

Silkscreen: Pa'epa'e

Togafitiga luga: ENIG

FPC mafiafia: 0.1 +/-0.03mm

Ituaiga Malosi: SUS

Min pu: 0.3mm

Pu tauaso:/

Tanu lua:/

Min Laina lautele / avanoa: 0.1/0.1mm

Fa'apalepale pu(nm): PTH: 土0.076, NTPH: 0.05

Fa'alavelave:/


Fa'amatalaga Oloa

Faailoga o oloa

Fa'amatalaga

Vaega Fa'agasologa Agavaa Vaega Fa'agasologa Agavaa
Ituaiga o gaosiga Fa'afuafua tasi FPC / Fa'asaga fa'alua FPC
FPC / Alumini PCBs tele
Ma'a-Flex PCBs
Numera Laega 1-16 laulau FPC
2-16 laulau Rigid-FlexPCB
HDI lolomi laupapa li'o
Max Gaosi Lafo Laega tasi FPC 4000mm
Fa'asaga fa'alua FPC 1200mm
Fa'ato'aga FPC 750mm
Malosi-Flex PCB 750mm
Laega fa'a'ese'ese
mafiafia
27.5um / 37.5/ 50um / 65/ 75um / 100um /
125um / 150um
Mafiafia laupapa FPC 0.06mm - 0.4mm
Malosi-Flex PCB 0.25 - 6.0mm
Fa'apalepale o le PTH
Tele
±0.075mm
Fa'ai'uga Faatofu Auro/Faatofu
Siliva/Gold Plating/Pin Plating/OSP
Fa'amalo FR4 / PI / PET / SUS / PSA/Alu
Tele Orifice Semili'o Min 0.4mm Min Line Avanoa/lautele 0.045mm/0.045mm
Onosa'i mafiafia ±0.03mm Fa'alavelave 50Ω-120Ω
Mafiafia Pepa Pepa 9um/12um/18um/35um/70um/100um Fa'alavelave
Puleaina
Onosa'i
±10%
Fa'apalepale ole NPTH
Tele
±0.05mm O le Min Flush Lautele 0.80mm
Min Via Hole 0.1mm Fa'atino
Tulaga
GB / IPC-650 / IPC-6012 / IPC-6013II /
IPC-6013III

Matou te faia PCBs fetuutuunai tasi-laupapa ma le 15 tausaga 'poto ma lo tatou tomai faapitoa

fa'amatalaga o oloa01

3 layer Flex PCBs

oloa-fa'amatalaga3

4 layer Rigid-Flex PCBs

fa'amatalaga o oloa03

8 lapisi HDI Lolomiina Boards Circuit Board

Meafaigaluega Su'ega ma Asiasiga

oloa-fa'amatalaga2

Su'ega Microscope

oloa-fa'amatalaga3

Asiasiga AOI

fa'amatalaga o oloa4

Su'ega 2D

oloa-fa'amatalaga5

Su'ega Impedance

oloa-fa'amatalaga6

Suʻega RoHS

oloa-fa'amatalaga7

Su'esu'e lele

oloa-fa'amatalaga8

Fa'ata'ita'i Fa'asaga

oloa-fa'amatalaga9

Pi'u Su'ega

O la matou 'au'aunaga PCB fe'avea'i fa'avae tasi

.Tuuina atu le lagolago faʻapitoa Faʻatau atu ma le maeʻa faʻatau;
.Fa'aleaganu'u e o'o atu i le 40 laulau, 1-2days Fa'atosina fa'ata'ita'iga fa'ata'ita'iga, fa'atosina tele, Fa'atauga o mea, SMT Fonotaga;
.E fa'amalieina uma masini fa'afoma'i, fa'atonuga o alamanuia, ta'avale, va'alele, mea fa'akomepiuta fa'atau, IOT, UAV, Feso'ota'iga ma isi.
.O matou 'au o inisinia ma tagata su'esu'e e fa'amaoni i le fa'ataunu'uina o ou mana'oga ma le sa'o ma le fa'apolofesa.

fa'amatalaga o oloa01
fa'amatalaga o oloa02
fa'amatalaga o oloa03
oloa-fa'amatalaga1

Fa'afefea ona fa'aogaina laupapa fa'asalalau lolomi e tasi-itu i uati

E masani ona fa'aogaina laupapa fa'asalalau lolomi e tasi-itu (PCBs) i le tele o talosaga mata'ituina, e aofia ai:

1. Faʻapipiʻi Faʻapipiʻi: O se PCB faʻapipiʻi tasi itu e tuʻuina atu ai se faʻavae mo le faʻapipiʻiina ma le fesoʻotaʻiga o mea faʻaeletoroni e faʻaaogaina i matamata e pei o microcontrollers, faʻaaliga, maʻa, ma isi vaega lagolago.O nei PCB o loʻo i ai faʻailoga apamemea mo le taʻavaleina o faailo eletise ma pads mo vaega faʻapipiʻi.

2. Fuafuaga fa'akomepiuta: Uati e masani lava ona la'ititi i le lapopoa, ma o le PCB fa'apipi'i tasi itu e mafai ai mo se mamanu fa'apitoa ma lelei.
O le fetuutuunai o le PCB e mafai ai ona punou, gaugau, pe faʻapipiʻi e fetaui i totonu o le avanoa faʻatapulaʻa o se uati aʻo tuʻuina atu pea se fesoʻotaʻiga eletise faatuatuaina.

3. Avanoa optimization: tasi-itu fetuutuunai PCB mafai ona faaaoga lelei le avanoa matamata.Ose laulau e tasi e mafai ai ona maua se fa'ailoga manifinifi, fa'asili le avanoa i totonu ma fa'ataga ai nisi vaega po'o galuega e fa'aaofia i totonu ole fua fa'atapula'a ole uati.

oloa-fa'amatalaga1

4. Fetuuna'i ma le Maumau: O le fetuutuuna'i o nei PCB e mafai ai ona latou tatalia le mamafa o masini e feagai ma le faʻaaogaina masani poʻo le faʻapipiʻiina o se uati, e pei o le punou ma le mimilo.O lenei fetuutuuna'i e sili atu ona latou tete'e atu i mea leaga ma faaletonu, ia mautinoa o le a tumau pea le galue o le uati tusa lava pe i lalo o le gaoioi faifaipea.

5. Faʻalagolago le fesoʻotaʻiga: O le PCB flex i le tasi itu ua mamanuina ma faʻailoga apamemea, lea e mafai ona maua ai le fesoʻotaʻiga eletise faʻalagolago i le va o vaega.O nei feso'ota'iga e taua tele i le fa'agaioiga lelei o le uati ma le sa'o o le taimi.O le faufale tasi e faafaigofieina ai le faagasologa o le faʻapotopotoga ma faʻaitiitia ai le avanoa o faʻafitauli fesoʻotaʻiga.

6. Gaosia tau-lelei: tasi-itu flex PCBs e masani lava itiiti lavelave ma manaʻomia ni mea itiiti ma gaosiga laasaga nai lo multilayer PCBs.O le mea lea e maua ai se faʻagasologa o le gaosiga e sili atu le taugofie, e faʻafiafiaina ai le au vaʻavaʻai e suʻe se fofo lelei.

7. Faʻasinomaga ma faʻapitoa: E mafai ona faʻapipiʻiina le PCB faʻapipiʻi tasi itu e faʻafetaui ai manaʻoga faʻapitoa o le matamata, e pei o se foliga faʻapitoa poʻo le tuʻufaʻatasia o galuega faʻapitoa.Matamata gaosi e mafai ona suia le tele, foliga ma le faatulagaga o le PCB e faʻaogaina elemene mamanu eseese poʻo le faʻaogaina o galuega faʻapitoa.

laupapa fetu'utu'una'i itu e tasi i matamata FAQ

1. O le a le laupapa malu e tasi itu?
- O le PCB fe'avea'i tasi itu o se laupapa fa'asalalau lolomi e iai fa'ailoga 'apamemea ma pa'u i le tasi itu.
Faia mai mea fetu'una'i e pei o le polyimide po'o le polyester, e mafai ona punou pe fa'apena e fa'afetaui ai mana'oga ma'oti o le uati.

2. O le a le faʻaogaina o laupapa fetuutuunaʻi itu e tasi i uati?
- O PCB fe'avea'i itu e tasi e fa'aogaina i mata'itusi mo le fa'apipi'iina o vaega, feso'ota'iga vaega fa'aeletoroni, ma tu'uina atu se fa'avae mo feso'ota'iga eletise.Latou te nafa ma le fa'aalaina o fa'ailoga i le va o vaega e pei o microcontrollers, fa'aaliga, ma'a, ma isi galuega matamata.

3. O le a le lelei o laupapa fetuutuunai itu e tasi i uati?
- O le PCB flex itu e tasi e ofoina atu le tele o mea lelei i le mataʻituina o talosaga.Latou te faʻatagaina mamanu faʻapitoa, faʻaoga lelei o avanoa ma fetuutuunai e faʻafefe ai le mamafa o masini.Latou te tuʻuina atu foʻi se fesoʻotaʻiga eletise faʻalagolago ma e mafai ona faʻapipiʻiina e faʻafetaui manaoga faʻapitoa.

oloa-fa'amatalaga2

4. E mafai ona punou pe fa'apena se PCB fe'avea'i itu e tasi ina ia ofi i totonu ole avanoa faatapulaa ole uati?
- Ioe, o PCB fe'avea'i tasi itu e fa'atatau tonu ina ia fetu'una'i ma e mafai ona punou pe fa'apena ina ia fetaui i totonu o fa'alavelave o le mamanu o le matamata.O lo latou fetuutuunai e mafai ai ona latou faʻafetaui i le avanoa avanoa e aunoa ma le faʻafefeina o fesoʻotaʻiga eletise.

5. E sili atu ona umi PCBs fe'avea'i tasi itu nai lo PCBs malo masani?
- Ioe, tasi itu-itu flex PCBs e masani ona sili atu le umi nai lo PCBs maumaututu ona o latou fetuutuunai.E mafai ona latou tatalia le punou, mimilo ma isi faʻalavelave faʻainisinia e faʻafeiloaʻi i le taimi e faʻaoga ai le matamata poʻo le faʻapotopotoga, ma faʻamalosia atili ai le faʻaleagaina ma le toilalo.

6. O se itu e tasi flex PCB tau-lelei mo le gaosiga o matamata?
- Ioe, tasi itu-itu flex PCBs e masani lava sili atu tau-lelei mo le gaosiga o matamata nai lo lavelave tele-layer PCBs.O la latou mamanu faigofie e manaʻomia ai le itiiti ifo o meafaitino ma laʻasaga o gaosiga, faʻaitiitia ai tau gaosiga.

7. E mafai ona fa'apipi'iina le PCB fe'avea'i tasi itu mo se mamanu mata'i faapitoa?
- Ioe, o le PCB flex itu e tasi e mafai ona faʻapipiʻiina e faʻafetaui ai manaʻoga faʻapitoa o le matamata.E mafai ona suia i le tele, foliga ma le faʻatulagaina e faʻaogaina ai elemene mamanu eseese poʻo le tuʻufaʻatasia o galuega faʻapitoa e tusa ai ma manaʻoga o le tagata gaosi oloa.

8. Po'o fa'aaogaina lautele le laupapa malu e tasi i le fale mata'aga?
- Ioe, e masani ona faʻaaogaina PCB faʻapipiʻi tasi itu ile fale mataʻituina mo o latou tulaga lelei eseese ma talafeagai mo mamanu laiti ma faʻatusatusa.O lo latou fa'aogaina o lo'o taatele i uati analog masani ma uati atamai fa'aonaponei.


  • Muamua:
  • Sosoo ai:

  • Tusi lau savali iinei ma lafo mai ia i matou